/ip address add address=192.168.21.2/24 interface=ether1 /ip address add address=192.168.1.180/24 interface=ether2 /ip route add dst-address=192.168.2.0/24 gateway=192.168.21.1 The route entry makes all packets with dst-address 192.168.2.x received from any interface, be sent through gateway 192.168.21.1, since that router is connected to the

To specify the interface in windows route command, you are supposed to use 'IF' Uppercase letters, not lowercase. Also, where you are specifying you want to add a route to a single IP 192.168.0.6, you need to use a subnet mask of 255.255.255.255. The subnet mask of 255.255.255.255 specifies a single host. If a static route needs to be persistent, add it to /etc/rc.conf: # Add Internal Net 2 as a persistent static route static_routes="internalnet2" route_internalnet2="-net 192.168.2.0/24 192.168.1.2" The static_routes configuration variable is a list of strings separated by a space, where each string references a route name. The below command is used to create Static Route for destination 10.10.20.0 /24 subnet behind router with IP 192.168.168.254 in X0 interface. config(C0EAE45BFFF0)# routing (config-routing)# route-policy interface X0 metric 1 (add-route-policy)# source any (add-route-policy)# destination name "Network Behind Router" (add-route-policy)# service any /ip address add address=192.168.21.2/24 interface=ether1 /ip address add address=192.168.1.180/24 interface=ether2 /ip route add dst-address=192.168.2.0/24 gateway=192.168.21.1 The route entry makes all packets with dst-address 192.168.2.x received from any interface, be sent through gateway 192.168.21.1, since that router is connected to the

The below command is used to create Static Route for destination 10.10.20.0 /24 subnet behind router with IP 192.168.168.254 in X0 interface. config(C0EAE45BFFF0)# routing (config-routing)# route-policy interface X0 metric 1 (add-route-policy)# source any (add-route-policy)# destination name "Network Behind Router" (add-route-policy)# service any

Dec 14, 2019 · The issue with the above command is when you shut down or restart the computer, these route entries will be removed. To make it permanent and add to the Windows OS routing table, we should use –p key with the route add command. So, adding a persistent (or permanent) static route on Windows 10 command will be like this; The routing switch also applies default values for the route's administrative distance (Administrative distance).In the case of static routes, this is the value the routing switch uses to compare a static route to routes from other route sources to the same destination before placing a route in the IP route table. Just like linux and unix environment, route command can be used to add static routes in Windows pc or windows server. There is a different between static route and persistent static route. Static route configuration will be erased after you reboot the machine. Note: Route uses a routing socket and the new message types RTM_ADD, RTM_DELETE, and RTM_CHANGE. As such, only the root user may modify the routing tables. If the flush or -f command is specified, route will "flush," or clear, the routing tables of all gateway entries. One can choose to flush only those routes whose destinations are of a given

To add a static route to a network, in other words to an IP address representing a range of IP addresses, issue the following command as root: ~]# ip route add 192.0.2.0/24 via 10.0.0.1 [dev ifname] where 192.0.2.0 is the IP address of the destination network in dotted decimal notation and /24 is the network prefix. The network prefix is the

To specify the interface in windows route command, you are supposed to use 'IF' Uppercase letters, not lowercase. Also, where you are specifying you want to add a route to a single IP 192.168.0.6, you need to use a subnet mask of 255.255.255.255. The subnet mask of 255.255.255.255 specifies a single host. If a static route needs to be persistent, add it to /etc/rc.conf: # Add Internal Net 2 as a persistent static route static_routes="internalnet2" route_internalnet2="-net 192.168.2.0/24 192.168.1.2" The static_routes configuration variable is a list of strings separated by a space, where each string references a route name. The below command is used to create Static Route for destination 10.10.20.0 /24 subnet behind router with IP 192.168.168.254 in X0 interface. config(C0EAE45BFFF0)# routing (config-routing)# route-policy interface X0 metric 1 (add-route-policy)# source any (add-route-policy)# destination name "Network Behind Router" (add-route-policy)# service any /ip address add address=192.168.21.2/24 interface=ether1 /ip address add address=192.168.1.180/24 interface=ether2 /ip route add dst-address=192.168.2.0/24 gateway=192.168.21.1 The route entry makes all packets with dst-address 192.168.2.x received from any interface, be sent through gateway 192.168.21.1, since that router is connected to the You can confirm whether new static route add been in route table using “ip route show” command. $ sudo ip route show. To add the specific IP of the backup server, say 10.0.2.15 run the command: $ sudo ip route add 10.0.2.15 via 192.168.43.223 dev enp0s3 Apr 17, 2011 · command: route add 192.168.1.1 mask 255.255.255.0 192.168.1.10. This is the simplest method of adding a temporary route. The subnet mask. parameter is optional and defaults to 255.255.255.255 which specifies that. the target is a single IP address instead of a network. An optional routing metric can be added to the route command for more Clish is a command line shell to configure Gaia OS and IPSO OS settings. To set a route (non-default): HostName> set static-route NETWORK_ADDRESS / MASK_LENGTH nexthop gateway address GATEWAY_IP_ADDRESS priority <1-8> on